Resetting your Holosun EPS Carry red dot sight back to factory settings can be a useful tool for troubleshooting issues or simply starting fresh. The process is fairly straightforward and only requires a few simple steps. Start by locating the reset button on the back of the sight. This small lever is often unmarked but can be easily identified by its position.
- Beginning a factory reset, you'll need to hold down the reset button for a period of time of approximately 4 seconds. You should see a blinking light on the sight indicating that the reset process is underway.
- When the reset is complete, the light will return to its default behavior.
- The red dot sight is now reset to factory defaults. You can then proceed with configuring it according to your desired setup.
Be sure to always refer to the user manual for specific instructions and details regarding your Holosun EPS Carry red dot sight.
Returning Your Holosun EPS Carry to Basic Settings
Need to Adjust your Holosun EPS Carry Optical back to its Initial configuration? It's Easy. Here's how:
First, ensure the Red Dot is On. Then, locate the Control labeled "Mode".
Press and hold this Control for approximately 3 seconds.
You should See a series of Changes on the Lens. This indicates that the EPS Carry is website now Back to Factory Settings to its Default configuration.
Once complete, release the Button. Your Holosun EPS Carry is now Operational with all settings at their Starting values.
Calibrating the Holosun EPS Carry Red Dot Sight
The Holosun EPS Carry Blue dot sight is a popular choice for concealed carry applications due to its compact size and durable construction. However, like any optical device, it may require periodic calibration. This can be easily accomplished by following these simple steps: First, locate the adjustment screws on the side of the sight. These are typically located near the battery compartment. Using a small tool, carefully turn the screws to fine-tune the point of impact. Start by making small adjustments and test fire the sight at various distances to ensure accuracy. Persist this process until you achieve a desired zeroing point.
- Keep in mind that the adjustment screws can be easily damaged if overtightened, so use caution when turning them.
- Guarantee that the battery is fresh and properly installed before making any adjustments.
- Should you encounter difficulty zeroing your sight, consult the manufacturer's instructions for further assistance or contact Holosun customer support.
Reset Factory Settings for Holosun EPS Carry
To reset your Holosun EPS Carry to its factory settings, you will need to navigate through the sight's menu system. First, turn on the optic by engaging the switch located near the side of the unit. Next, utilize the tactile buttons found beside the holographic display to access the settings menu. Within the menu, locate the "Factory Reset" option and choose it using the designated button. The EPS Carry will then initiate a reset sequence, which may take a few moments. Once complete, your sight will be restored to its default configuration.
- Note: During the reset process, all user-configured settings will be erased.
Reset Your Holosun EPS Carry Effortlessly
Need to get your Holosun EPS Carry back to factory settings? It's easier than you think! Here are the simple steps you need to follow:
First, turn off your red dot. Then, find the tiny reset button on the side of the sight. Use a small tool like a paperclip or a pin to press and depress the reset button for about 5 seconds. You'll know it worked when the display starts flashing.
- Let the sight to cycle through its startup sequence. This might take a few moments.
- Your Holosun EPS Carry is now reset to factory default settings!
Return to Factory Settings a Holosun EPS Carry Red Dot
Need to new configuration setup? Here's how it's done to Factory Reset your Holosun EPS Carry Red Dot.
First, make sure the red dot is activated. Next, pinpoint the tiny button on the left/right side of the sight's housing/body. Press and hold this button for a minimum of 5 seconds/3 seconds. You should notice a flashing light/blinking indicator indicating that the reset process has begun/started. Keep holding/pressing the button until the light stops blinking/flashing. Let go the button and your Holosun EPS Carry Red Dot is now completely reinitialized.